GHG 26 / EXKO 2.. Ex-Safety Switches

GHG 26 / EXKO 2.. Ex-Safety Switches
Donat Czapski

Donat Czapski – I am at your disposal

+48 695 244 220


We know the requirements of insurers

From ATEX AUDIT to protection implementation

We provide 24/7 service

GHG 26 / EXKO 2.. Ex-Safety Switches

Rated current from 10 A – 630 A

CEAG safety switches can be protected against inadvertent switching on by our integrated locking facility for up to three padlocks in the OFF position. To prevent manipulations, the enclosure covers cannot be opened in the locked position without destroying the enclosure itself.

Full AC-3 switching capacity

All CEAG safety switches feature full AC-3 motor switching capacities and isolating properties according to EN 60947-4-1 with compulsory opening of the main current contacts; optional EMERGENCY STOP versions according to EN 60204-1 are also available. An additional lagging/leading auxiliary contacts (option) guarantee double safety for extreme switching conditions.

Installation-friendly design

The safety switches feature an installation-friendly design and easily accessible connection terminals.

Versions in impact-resistant polyamide or glass-fibre-reinforced polyester enclosures provide the high degree of protection IP66 for safety switches up 180 A. These can be optionally supplied with snap-on moulded plastic or brass flanges. Safety switches for amperages up to 630 A are supplied in metal enclosures. These can be equipped with screw-on flanges.

Explosion Group IIB

The described safety switches at the sizes 210 – 630 A are also available for Explosion Group IIB, which is sufficient for many of the applications.Enclosed Switch-Disconnectors to provide isolation during repair and maintenance.

GHG 26 switches (10-160 A) and GHG 981 switches (25 – 80 A) are now confirmed to comply with the new standard IEC 62626-1, requirements Class 1. The new standard IEC 62626-1 defines the requirements for safety switches (switch-disconnectors) that are used to provide isolation of equipment during repair and maintenance. These requirements go above and beyond those of IEC 60947-3, where no standard previously existed.

The standard divides products into two classifications:

  • Class 0 for general use and
  • Class 1 for harsh and rough/heavy duty conditions.

All products installed in ATEX/IECEx hazardous areas should be rated for Class 1. Class 1 requirements include minimum ratings for mechanical strength, IP protection, tamper resistance, heat/vibration/corrosion resistance, switching capacity, and locking capability.

  • Full AC-3 switching capacity
  • Double safety: additional auxiliary contact
  • Cost-saving installation up to 180 A
  • Snap-on mounting up to 40 A
  • IP66 protection up to 180 A
  • GHG 261 – Ex-safety switches 10 A
  • GHG 262 – Ex-safety switches 20 A
  • GHG 263 – Ex-safety switches 40 A
  • GHG 264 – Ex-safety switches 80 A
  • GHG 265 / EXKO 2 – Ex-safety switches 125 A
  • GHG 266 / EXKO 2 – Ex-safety switches 180 A
  • EXKO 7317 – Ex-safety switches 210 A
  • EXKO 7317 – Ex-safety switches 250 A
  • EXKO 7317 – Ex-safety switches 400 A
  • EXKO 7317 – Ex-safety switches 630 A
  • GHG 262 – Ex-safety switches for three-phase drives 20 A
  • GHG 263 – Ex-safety switches for three-phase drives 40 A
  • GHG 264 – Ex-safety switches for three-phase drives 80 A

Ex Electrical Equipment – offer

GRP Ex Terminal Boxes HARDO


Increased insulation clearances of built-in components, high IP rating of enclosures, temperature restrictions, use of certified components and certified electrical equipment.

aluminum control stations hardo


The offered control stations and panels can be operated even under extreme industrial conditions. Our enclosures are resistant to corrosion and the effects of aggressive chemicals.

Explosion-proof cable glands for armored cables HARDO

EX Cable

Ex cable glands are used wherever a properly protected connection of armored or non-armored cable to machinery or equipment is required.

eXLink - the Miniature-Power Connector


ATEX certified round plugs and receptacles – contact-making insert can be arranged in various positions

Our own

Guaranteed high quality due to total control over the product at each stage of the manufacturing process. Quick implementation due to shorter lead times for non-standard solutions

Secure your industrial plant

Do you have any questions?

Donat Czapski Grupa WOLFF zdjecie
DONAT CZAPSKI - I am at your disposal

We will answer questions about: offer, technical specification, delivery, assembly.

or send your inquiry